A: RP-SMA Connector
B: Video Status
C: Link Status
D: Power Status
E: Fault LED
F: Mini USB Port
G: HDMI Input
H: Power Switch
I: 7-28V DC Input
J: 3G-SDI Output
K: 3G-SDI Input
L: SDI Status
M: HDMI Status
N: USB Status
O: Fault/Error LED
P: HDMI Output
Q: Status Joystick
R: Menu Joystick
S: Link Quality Indicator
T: USB 3.0 Port
Bolt Pro 600/2000 TX Bolt Pro 600/2000 RX
A
B
C
D
E
G
F
H
S
T
C
B
R
Q
I
J
K
A
H
F
I
M
N
O
L
J
P
SDI
HDMI
NEED MORE HELP?
1. Support forum: http://support.teradek.com → Contains tips, information and all the latest firmware & software updates.
2. Training videos: http://www.teradek.com/training
TERADEK SUPPORT STAFF: support@teradek.com or call 888−941−2111 ext2 (Mon−Fri 7am to 6pm PST)
Bolt Pro 600/2000
CONNECT AND POWER YOUR DEVICE
Connect the output from your video source to the SDI/HDMI input (G) on the Bolt
transmitter. Connect either the SDI or HDMI output from the Bolt receiver to the
video input on your monitor.
Uncompressed
Long-Range
Wireless HD Video
The Bolt Pro is a zero delay
wireless video transmission
system designed for the
most demanding cinema,
broadcast, and UAV
applications. At less
than 1ms latency, Bolt Pro
can transmit 1080p60 4:2:2
video at up to 2000ft line
of sight over the unlicensed
5GHz band.
Attach the two TX antennas to the transmitter and the five smaller RX antennas to
the receiver via the threaded RP-SMA connectors (A).
Move the power switches on both the transmitter and receiver (H) to the ON position.
Video appears within a few seconds.
Connect power to your Bolt transmitter using the included P-Tap to Lemo cable.
Power the Bolt receiver with the included A/C adapter or battery plate accessory. If
using the battery plate, connect a compatible battery (AB Gold mount or V-Lock) to
the plate, and connect the short cable from the plate to the receiver’s DC input (I).
1
3
4
2
AC adapter
P-Tap to Lemo
Status Screens - Cycle through status screens or return from the menu by pressing the red ‘Status Joystick’. (Q)
• Main Status Screen - This screen displays the status of the wireless receiver, along with the current video
resolution, frequency, and link quality (if connected).
• Time Code Screen - Displays the current time code if received from the transmitter.
• Temperature Status Screen - Displays the current internal temperature of the unit.
Menu Operation - launch the menu and navigate through it with the black ‘Menu Joystick’ (R).
• HDMI/SDI Out Format - Select the video output format. You can choose to match the video source
resolution by selecting ‘Same as Input,’ or choose from the resolutions listed.
• Test Pattern - Select a video output format from this menu to output a test pattern over HDMI and SDI.
Return to the previous video by pressing left on the ‘Menu’ Joystick.
• Pairing - Select Pairing to link your receiver with another transmitter. Once pairing is activated on the
receiver, turn on the transmitter and use a paper clip to hold the reset button (between the DC input and
power switch) for 3 seconds and release. The red warning LED and link LEDs will blink to indicate that
pairing is active.
• Video Loss Settings - Choose what is displayed when no video is received from the transmitter. The default
selection (“Show OSD”) will display messages about the state of the receiver. These can be disabled by
selecting “Show Black Screen.”
• Display Settings - Use these options to control the OLED display operation. You can set the display to
invert every 30 minutes (lengthens the display life), or it can dim or turn off after 10 seconds or 10 minutes.
• Reset All Settings - Use this to reset all configurable options to their factory defaults.
• Device Info - Displays the model and serial number.
FRONT PANEL OPERATION
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals